Network Interface Cards

As we know from the Wikipedia, a network interface card, known as Fiber Optic Network Interface Card, which is simply a computer circuit board or card that is installed in a computer so that to connect to the network. Personal computers and workstations on a local area network (LAN) typically contain a network interface card specifically designed for the LAN transmission technology, such as Ethernet or token ring. NIC adapter hardware is the form factor os an add-in card such as PCI card.

NIC cards work with wired or wireless connection, as they support either wired Ethernet or Wifi wireless standards. Ethernet NICs plug into the system bus of the PC an include jackets for network cables, while WiFi NICs contain built-in transmitters/receivers. In most computer nowadays, many NICs are pre-installed by the manufacturer. They features a speed rating such as 11 Mbps, 54 Mbps or 100 Mbps that suggest the general performance of the unit.

PCI and PCI Express

PCI is short for Peripheral Component Interconnect. It is regarded as a local computer bus for attaching hardware device in a computer. PCI is part of local bus standard. The PCI bus supports the functions found on a process bus but in as standardized format that is independent of any particular processor’s native bus. PCI has been a versatile, functional way to connect sound, video and network cards to a motherboard.

As processors, video cards, sounds cards and network has gotten faster and more powerful, the shortcoming of PIC appears. Because PCI has a fixed width of 32 bits and can handle only 5 devices at a time. To overcome these shortcomings, the PCI Express appears with improvements over the old PIC, including higher maximum system bus throughput, lower I/O pin count and smaller physical footprint, better performance-scaling for bus devices, a more detailed error detection and reporting mechanism and native hot-plug functionality.

A key difference between PCI Express bus and older PCI is the bus topology. PCI uses a shard parrel bus architecture, where the PCI host and all devices share a common set of address/data/control lines. In contrast, PCI Express is based on point to point topology, withe separate serial links connecting every device to the root complex.

Gigabit PCI Express Network Card

Gigabit PCI Express network card is gigabit based network adapter card that offers a versatile solution that allows servers and desktop PCs to connect to a Gigabit network through a PCI-E slot. It can provide full Gigabit bandwidth capacity with the dedicated bandwidth of the connected PCI Express bus to provide dependable connectivity. Gigabit PCI express network card is fully compliant with the 10/100/1000 Mbps IEEE 802.3 specification, this PCIe Gigabit NIC provides a maximum transfer speed of 1000Mbps (bidirectional - 2000Mbps total) - ensuring a high performance network connection. This adapter also offers 10/100/1000Mbps data rate auto-negotiation and full duplex operation that helps to optimize connection speeds and provide efficient performance.

As a professional fiber optic network solutions provider, FiberStore offers full ranges of PCI network interface cards includes 100M PCI/PCI-E NIC, PCI-E 1000M NIC,and PCI-E 10G SFP+ Ports. For specifications of each type, please welcome www.fiberstore.com

Digital Video technology is emerged as the ultimate facilitator of surveillance needs and has played an important role in the security area, that enables flexible, real-time, highly manageable and tunable solutions. The digital video multiplexer combined with Wavelength Division Multiplexer technology, making it possible to extend video and data service up to 100km distance simultaneously through one single fiber, and get the real-time high-definition video on the receiver side. Fiber digital video multiplexers are commonly used for security application to control and monitor video cameras signals in airports, train station and public hotspots.

FiberStore provide digital video multiplexers for video/audio/data signal transmission. These video multiplexers are single mode and multimode fiber type with 1 to 64 channel signals in different optical distance. They can either be track mountable or standard units. FiberStore also provide insert card version, which can be inserted into the 16-slot, 19inch 2U or 4U rack-mountable card cage for 10-digit coding and non-compression video transmission.

Typical fiber ports of these multiplexer are FC, SC or ST with interfaces of RS422, RS485 or RS232, making it workable with series to date fiber media converters such as RS422, RS485 or RS232 fiber convertersperfectly.

1-64 Channel Video Multiplexers Video multiplexer are built on CWDM and can encoded multi-channel video signals and convert them to optical signals to transmit on optical fibers. It handled several video signals simultaneously, and can provide simultaneous display and playback features. With a video multiplexer, users can record their combined signals on the VCR or where else they want to record.

Digital multiplexer has two VCR IN connections and two VCR OUT connections. There is one pair of VCR IN/OUT 4-pin DINI connectors (Y/C) and one couple with BNC connections (composite video). The VCR IN connectors is used to connect the multiplexer to a VCR which will be used to playback recorded images. Connect the Video OUT connector on a VCR to one of the VCR IN connectors on the multiplexer. The VCR OUT connectors are used to connect the digital multiplexer to a VCR which will be used to record video. Connect the Video IN connector on a VCR to one of the VCR OUT connectors on the multiplexer.

Video data multiplexers are based on digital video technology to provide fiber optic transmission of video and return or bidirectional data signals in demanding environments. They can provide highly reliable data transmission and expandable data capacity over fiber optic cables up to a few tens of kilometers. The video data multiplexers simultaneously transmit multi-channel 8-bit digitally encoded broadcast quality video over one multimode or single mode optical fiber.

This module is directly compatible with NTSC, AL, or SECAM CCTV camera systems and support RS-485, RS-422, and RS-232 data protocols. These muxes are typically used with cameras that have PTZ capability. The plug and play design ensures adjustment-free installation and operation. LED indicators are provided for instant monitoring system status.

Video and Audio Multiplexer combines digital video with digital audio to form the embedded signal. It has optical remote monitoring capabilities so that operation can be controlled remotely. The audio video multiplexer can simultaneously transmit 1-64 channels of 8-bit digital encoded broadcast quality video/unidirectional or bidirectional audio signals over multimode or single mode optical fiber. These multiplexers are used in applications where the cameras have P/T/Z capabilities.

Video/Audio/Data Multiplexers transmit 1-64 channels of 8-bit digitally encoded broadcast quality video/return or bidirectional data/unidirectional or bidirectional audio over one multimode or single-mode optical fiber. These multiplexers are used in applications where the cameras have P/T/Z capabilities. With Plug and Play design, it can convert, integrate, groom and multiplex multiple video/audio/data streams effortlessly.

The Video & Data & Audio Multiplexers are ideal for a wide range of multiplexing and re-multiplexing applications including Broadcast/Studio, CCTV audio and Professional AV applications.

FiberStore has been providing quality fiber optical cabling and connectivity solutions to datacomm and telecommunication industries to worldwide customers for over ten years. As a specialized fiber optic cables and patch cables manufacturer, we have conducted rigorous quality controls on each manufacture steps, to make sure that all of our fiber optic cables are completely ROHS and REACH compliant. Our fiber optic patch cables are classified to common OM1, OM2, OM3, OM4 patch cables, Armored fiber patch cables, related fiber cables, as well as the multi core fiber patch cables.

Among these, multi-fiber optical patch cable includes the trunk common connector type multi-core fiber patch cable and MTP fiber patch cable. Multi core fiber patch cable get its name as it is consist of multi core fiber, which also called multi fiber patch cable. Multi core fiber patch cables is mostly commonly used for trunk cable plant and can be as the distribution or breakout patch cable. We offer the common fiber trunk patch cables with SC, LC, FC, ST, MTRJ, MU, E2000 connectors at both end. For each connector type, like LC, there are LC-LC connector, FC, SC, ST, MTRJ, MU, E2000, LC to SMA. They are optically and electrically inspected and tested using accepted industry test procedures as recommended by the most current version of ANSI/TIA-455B standard test procedure for standard fiber optic fiber, cables, transducers, sensors, connecting & terminating devices, and other components.

MTP hybrid patch cable with one MTP connect at one end, and other common connectors like SC, LC, FC, ST, etc. at the other end to connect with the some connector multi fiber patch cables. Since the MTP connector is almost the same size with the common connectors, but it can accommodate 12 fiber into one connector, thus it provides up to 12 times the density of the stand multi core patch cables. MTP fiber patch cable includes the MTP standard and hybrid trunk cable. MTP trunk patch cables are calassified classified into standard MTP to MPO/ MTP to MPO fiber connector trunk, MTP hybrid (MTP to common connectors) trunk cable. Similar with the MTP cassettes, MTP patch cable make it is possible to run a single cable automatically terminated with up to 12 fibers in one single plug in.

The multi core fiber patch cables features includes:

Multi-fiber channel options

Various option of fiber and connector types

Standard or custom configurations

Easy to use, easy to install and maintain

Low insertion loss and back reflection

Custom defined specifications

Environmentally stable

Complete with orange OFNR rated riser/jacket

100% optically tested to ensure high performance

According to different requirements, 4 to 966 cores are available

Applications

FTTH, LAN, Test equipment, Military industry

CATV

Outside plant

Premise networks

Aerial distribution

Measuring equipments

Fiber optic communication system

Optical active component and equipment

We offer customization solutions for these multi core optical patch cables with options of any fiber type, any connectors, and lengths and even customer logo and label on fiber patch cables. Fiber types is selectable from 10G OM3, OM4 optical fiber, single mode 9/125 optical fiber, OM1, OM2 multimode 50/125 fibers.

As is well known that a hybrid fiber coaxial (HFC) network is a telecommunication technology in which optical fiber cable and coaxial cable are used in different portions of a network to carry broadband content. By using HFC, a local CATV company installs fiber optic cable from the cable head-end to serving nodes located close to business and residential users and from these nodes uses coaxal cable to individual businesses and homes. The various services are encoded, modulated and upconverted onto radio frequency (RF) carriers, combined onto a single electrical signal and inserted into a broadband optical transmitter.

CATV fiber optic transmitter is a special optical transmitting equipment in HFC broadband transmitting network. It converts the electrical signals to a downstream optically modulated signal that is sent to the nodes. Fiber optic cables connect the headend or hub to optical nodes in a point-to-point or star topology, or in some cases, in a protected ring topology.

FiberStore’s CATV optical transmitter series offer great flexibility to meet the demands of todays’ CATV requirements. These transmitters use directly modulated DFB technology for transmission of optic signal at 1310nm wavelength, and utilize superior circuit design to support automatic temperature and power control. They are mainly used to transmit analogy TV signal, digital TV signal and INTERNET data signal in 860MHz frequency.

According to the different application, these 1310nm optical transmitters are divided into indoor and outdoor type, with either standard MGC or AGC function. The pre-distortion circuit makes product have excellent non-linear index, ensure optical fiber network and long distance transmitting, make out users cover. RF-input point and power supply with lighting proof, the waterproof design also make it suitable for any bad outdoor environment. AGC optical transmitter, with MCU monitoring circuit to control the working status of the laser, it will display in the LCM/VFD on the front panel, and can be interfaced with a network management system via a RS232 or RS485 port for status monitoring.

Specifications

Power: 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26

Fiber Type: Single mode

Bandwidth: 45~750/862MHz

Flatness: ±0.75dB

Input Return Loss: 16dB(45~750/862MHz)

Input Impedance: 75Ω

RF Gain Adjustment Range: 0~10dB(AGC/MGC)

RF Input Signal Level Range: 75dBμV~85dBμV

RF Connector Model: F-connector(mm/inch)

Power Supply: 220V(110 ~265V/50Hz)

Laser Type: DFB

Optical wavelength: 1310±20nm

Optical Power(Optical Path Loss): 468~24mW

Applications:

1310 broadcast and narrowcast applications

CATV forward path

RF over fiber

About FiberStore

FiberStore is a leading manufacture of broad range of fiber optic and copper data communication cabling and connectivity solutions primarily for the enterprise market, offering an integrated suite of high quality, warranted products which operate as a system solutions for seamless integrate with other providers' offerings. Our fiber optic transmission products includes fiber tansceivers,ethernet to fiber converter, digital video multiplexer, HFC network devices, etc. Welceome to visit www.fiberstore to get the customized fiber optic network solutions.

FiberStore is a 10G fiber system offering OM3 OM4 10G 50/125 fiber optic cable fiber cable and single mode fiber cables in full compliant with IIEC 60793-2 and TIA 492AAAC DMD. Both OM3 and OM4 can support of 10Mbps transmission over 550m and also 1000Mbsp over 1100m. The OM3 OM4 fiber cables works in full harmony with the fiber patch panels and components in order to support the existing network topology and can be deployed in either the backbone or horizontal cabling.

FiberStore provide wide range of 10G OM3 OM4 fiber cabling solutions including 10G fiber cable, patch cables. The bulk 10G fiber cables support a broad range of legacy and 10Gb/s applications as their special bandwidth performance. Custom options of these 10G fiber optic cables are:

Fiber Coloring: blue, orange, green, brown, slate, white, red, black, yellow, purple, rose, aqua or custom specified

Fiber Type: Single-mode, Multimode

Sheath Color: black, blue, orange, green, brown, slate, white, red, yellow, purple, rose, aqua or custom specified

Sheath Material: PE, AT or custom specified

Cable Length: Custom specified (minimal length is 3m)

10G fiber optic patch cable are also manufactured and 100% optical tested for maximum performance. Customer can also custom the 10G OM3, OM4 fiber cable with any connector types such as LC-LC, LC-SC, SC-SC, FC, MTRJ, MU, MPO/MTP etc and any cut lengths. Besides, as a professional fiber optic products manufacturer, we also provide 10G SFP+ fiber optic transceivers like Cisco SFP-10G-LR, SFP-10G-SR, etc. to work with these 10G fiber optic cables. We can supply these 10G fiber optic cables and 10G fiber transceivers according to customer's requirement, and design labels and packaging for them.

There are two major types of fiber optic adapters mating sleeves and hybrid adapters. The mating sleeves means the fiber optic adapters are used to connector the same type fiber optic connectors, bare fiber type and plug-in type are available for the mating sleeves, while hybrid adapters are used to connect different kinds of fiber optic connectors. FiberStore supplies all plug-in, bare and hybrid type fiber adapter for single mode and multimode, simplex and duplex applications.

Hybrid fiber adapters provide interconnection between two different fiber connector types. It includes male-female hybrid fiber adapter and female-female hybrid fiber adapter. Femele-Female hybrid fiber adapter is a fiber adapter with two different ends, which is bulk type hybrid fiber adapter. Such as FC female at one end, ST female at the other end. Male-Female hybrid fiber adapter is build out type with a connector plug end and an adapter socket end. FC-SC Hybrid SM fiber adapter is used to connect fiber optic connectors single mode FC and SC fiber optic cable together.

FiberStore provide a complete line of adapters for optical fiber connections, including ST, SC, FC, LC, MTRJ, MPO and MU connector type. By using high quality raw materials, we make our fiber optic adapters strictly according to international standard, and fully compatible with other products from other manufacturers in the market.



Welcome to our product page of Hybrid Fiber Adapter, in which you can find detailed specification of Hybrid Fiber Adapter. The hybrid fiber adapter is good in quality and competitive in price. Besides, FiberStore supply OEM service for this fiber adapter and can manufacturer them according to your special requirement. We can also customize the logo, package, brand for customers’ companies. Feel free to visit www.fiberstore.com

FiberStore offers many kinds of network cable tester including LAN network cable testers, LCD cable testers, underground wire locators, network cable scanner, etc. In this article, we will mainly introduce one of the main LCD cable tester - Wireless network LAN phone cable LCD tester meter SC-8108

This Multi-Network cable tester is a powerful tool to prevent and solve cable installation problem. The tester will automatically detect far-end matcher (ID) or local port (L) cable and displays if the far-end of cable to be checked does not insert into the far-end matcher (ID) or if the cable does not insert into the local port (L) in local test. This network cable tester instantly check your LAN cable wiring for proper continuity, shorts, and pair integrity. Test results are digitally shown via its LCD and it instantly displays the exact configuration of the cable. It performs line test without requiring the external adapter. With single board computer software watchdog design and reliable operating time. This covers wide array of applications such as cable connection sequence, length, user jumper or crossfire, cable connection continuity and determine any open circuit, short circuit, jumper or cross-talk interference.

Key Description

Power Supply

The tester uses 4 x 1.5V size AA alkaline batteries with power consumption 16 mA. The batteries should be taken out if the tester does not use for a long time to prevent the battery rack from leaking electrolyte corrosion.

Tester Panel and Port

Loopback port

Main port

LCD display screen

Power switch

Function key

Confirmation/return key

Specifications

Type of Tester Cable: STP/UTP twin twisted cable, coaxial cable, telephone line

Tester Port: Tester RJ45 master port (M), tester LOOPBACK RJ45 port (L), far-end recognizer RJ45 port (R)(BNC and RJ11 converters (not included in the set), can be used to measure and check the continuity of coaxial cable and telephone line)

Length Measurement of Twin Twisted Cable: Scope: 1 to 350M (3 to 1,200 FT) calibration; Calibration accuracy: 3% (± 0.5m or ± 1.5 ft) (calibrating cable > 5 M);

Shipment accuracy: 5% (± 0.5m or ± 1.5 ft) (AMP, AT&T Class 5 cable); Unit of Measurement: Display in meter (M) or feet (FT)

Length Calibration:User can set self-calibration factor by a given length cable. The length of calibrating cable is more than 5M

Wire Sequence and Locating Cable Error: Check errors such as open circuit, short circuit, reverse connection, cross over or cross-talk interference

Locating Cable: Included 1 far-end passive test jack

Powerd by: 4 x AAA batteries

Automatic Time-delay Shut Off Time: The tester is idle for 30 minutes

Working Ambient Temperature: -10°C to 60°C

LCD size: 2.6"

Color: Grey

For more information about the LAN Phone Cable LCD Tester Meter SC-8108, please visite www.fiberstore.com

FiberStore, as the major global fiber optic tools provider, is proud to become the agent for the original Miller fiber optic tools. Our Miller fiber optic tools include fiber scribers, cable Strippers, cutting tools and Kevlar shears.

A precise stripper is utilized to remove the buffer coating of the fiber itself for termination. There are three types of fiber strippers available, known as the Miller Stripper, No-Nik and Micro-Strip. These three can work equally well, and most techs choose the one they are most acquainted with. The Miller striper is used on the left thus has the disadvantage of being "right-handed", Which is considered to be the most rugged. The No-Nik is careful with the fiber but requires careful cleaning. Check out the original Miller Fiber optic stripper features:

Miller Fiber Optic Stripper FO 103-D-250

New Dual holes models offer he same quality of our standard FO 103-S fiber tool coupled with a second hole

FO 103-D-250: Second hole for stripping 900 micron tight buffer down to 250 micron buffer coating and standard 125 micron fiber stripping (250 micron removal to 125 micron) – allows longer

Stripping lengths without damaging the fiber

Easy-to-read stripping diagrams imprinted on handles

Made in the U.S.A.

Length: 5.375 in (137mm)

Weight: 2.5 oz (71g)

Miller Fiber Optic Stripper FO 103-T-250-J

New three-hole model performs all common fiber stripping functions in one compact tool....

Hole for removal of 2 to 3 mm fiber jackets

Remove 900 tight buffer to 250 micron buffer coating

Standard 250 to 125 micron stripping

Same consistent quality and features found in our standard FO 103-S tool

Made in the U.S.A.

Length: 5.375 in (137mm)

Weight: 2.5 oz (71g)

Miller FO 103-S Fiber Optic Stripper

For stripping 250 micron buffer coating from 125 micron optical fiber

Precision diameter hole & V-opening in blade allow for accurate buffer coating removal

NEW pivot pin, spring and precision handles enhances tool functionality and durability

Factory set, requires no adjustment

Prevents scratching or nicking of optical fiber

All cutting surfaces are precision formed, hardened, tempered and ground assuring precise buffer removal

Made in the U.S.A.

Length: 5.375 in (136.53mm)

Weight: 2.5 oz (71g)

Miller Fiber Optic Stripper CFS-2

For stripping 250 micron buffer coating to expose 125 micron cladding fiber

Second hole for stripping 2-3mm fiber jackets

140 µm diameter hole and V-opening in blade allows removal of 250 micron buffer coating from 125 micron fiber

Pre-set at the factory - no adjustments needed

Will not scratch or nick glass fiber

All stripping surfaces are manufactured to precise tolerances to assure clean, smooth strips

Comfort-grip, ergonomic handles

Lock to hold tool closed when it is not in use

Length 6.43 in (165.00mm)

Weight 4.17 ounces (119.0g)

Most strippers are "sized" for the fiber coatings to be removed. So ensure you have the proper stripper for the fiber being stripped. Whichever stripper is used. Care must be taken to not nick the Fiber during the stripping process as it can cause cracks that may lead to fiber failure sometime in the future. Strippers require careful cleaning and immediate replacement if they become damaged or worn.

Strippers are sized for the fiber coatings to be removed. So ensure you have the proper stripper for the fibers to be stripped. Whichever stripper is used, you must take care to not nick the fiber during the stripping process as it can cause cracks that may lead to fiber failure sometime in the future. FiberStore.com supplies various of high quality fiber optic tools individually or in kits, most of the price is extremely cheap, even the fiber optic tool kit price is with attractive discount rate.

Bare fiber adapters enable quick and easy temporary connections of single mode and multimode fibers. These adaptors are very useful for connecting fibers to fiber optic power meter, optical time-domain reflectometers (OTDRs) and a variety of other instruments, enabling in-situ functional testing without having to attach a permanent connector.

Bare fiber adapters provide a simple and effective way to use un-terminated fibers with commercial receptacles. Here is the installation guide for the bare fiber adapters.

Attaching the patch cord

Clean connectors on fiber jumper or launch reel. Position connector on fiber jumper or launch reel with bare fiber adapter connector port. Insert the connector into the bare fiber adapter connector port until hear a click.

Preparing the fiber

Remove 6 inches of jacket and Kevlar. Remove 1 inch of coating and cladding. Cut the fiber 12mm-15mm long with fibre cleavers

Inserting the fiber

Clean the bare fiber. Press and hold down the button (There is a button on the adapter) while slowly and carefully inserting the bare fiber into the fiber port. Open the window to visually see the proper alignment of the bare fiber in the V-groove. To prevent accidental breakage of the glass fiber, slowly insert 1/8 inch to 1/4 inch of fiber at a time. Rotate the fiber until the glass aligns with the v-groove to enter the connector port. Push the fiber until it stops in the connector port After that, releaser the button to secure the fiber.

Removing the fiber

Press and hold down the button while slowly and carefully pulling the bare fiber out of the fiber port. Be sure to check for any broken glass fiber pieces after removing the bare fiber from the adapter.

Removing the jumper cable

Slowing pull the fiber jumper connector out the connector port. Broken fibers are easily removed with piano wire, allowing hundreds of insertions.

FiberStore supply the largest selection of bare fiber adapters connector styles on the market including SC, ST and FC bare fiber optic adaptor with stable qualities. These adapters use high quality ceramic ferrules and precise fiber connector housing parts, they are used to quickly and easily terminate the fiber to the equipment.

Fiber multiplexer is powerful communications equipment. They allow mixing of T1/E1, Ethernet, POTS ports (FXO or FXS) and serial datacom interfaces such as V.35, RS-232, X.21 etc. Together on a single circuit of fiber optic, so that fiber is saved and higher density and capacity networks can be put together. FiberStore multiplexers are supported by industry leadership in fiber optic development, including optical sensors, telemetry systems, connector design, ruggedized optics, and the widest selection of Fiber Optic Rotary Joints (FORJs). All of these fiber optic multiplexers supports remote management and have optional service line ports. Capacity starts with 4T1 or E1 interfaces on low entry models and goes up to 63T1Ss or E1s together on a single strand of fiber optic cable.

Typical optical multiplexers are Video & Data & Audio Multiplexers, PDH Multiplexer. Custom solutions provide support for additional signal formats or unique combinations of standard protocols. Application specific products can be also customized to reduce size or cost, optimize packaging, extend environmental performance, and integrate more directly with other equipment.

Video Multiplexers

Video multiplexer is used to encodes the multi channel video signals and convert them to optical signals to transmit on optical fibers. It handles several video signals simultaneously and it can also provide simultaneous playback features. With the video multiplexer, you can record the combined signal on your VCR or wherever else you want to record.

Video & Data Multiplexers

FiberStore video & data multiplexers provide high reliable fiber optic transmission of video and data signals in demanding environments. A wide range of supported video and data formats ensure the flexibility needed for easy system configuration. Individual data channels can be mixed and matched with a variety of plug-in interface modules. Advanced optical multiplexing (CWDM, DWDM) enables system expansion to 32 video and 256 data channels as well as additional high data rate signal such as HD-SDI, ECL for advanced sonars, and Gigabit Ethernet.

Video & Audio Multiplexers

Video and audio multiplexer combines digital video with digital audio from the embedded signals. It has optional remote monitoring capabilities so that operation can be monitored remotely. Video & Audio Multiplexer is widely used in security monitoring and control, high way, electronic police, automation, intelligent residential districts and so on.

Video & Data & Audio Multiplexers

Video/data/audio multiplexers are designed for users to convert, integrate, groom and multiple video/audio/data streams effortlessly. These multiplexers can transmit and extend a maximum of video, audio and data over fiber cables up to a few tens of kilometer. They are ideal for applications like Broadcast/Studio, CCTV audio and professional AV applications.

FiberStore now offer a full range of multiplexer products, from single channel media converters for Ethernet and HD-SDI to multi-channel CWDM and DWDM multiplexer supporting 16 or more video lines, 128 serial data channels, multiple digital I/O, plus 10/100/100M Ethernet and high bandwidth sonar interfaces, all on a single optical fiber.